The Street Diesel (SD) class is designed for full bodied, four wheel drive or two wheel drive pickup trucks on the ragged edge of street-ability.
Designations: SD followed by the Competition number.
Weight: 8000 lbs. Maximum, with driver.
Ballast: Ballast is permitted. Hanging weights may not extend more than 60 inches from the centerline of the front axle.
Batteries: The batteries must be securely mounted. They may not be located in the driver compartment but can be located in the truck bed or forward of the radiator core support.
Body: The body must be an OEM truck body, including the full bed floor. The body must retain full sheet metal. Metal aftermarket hoods are permitted. Fiberglass is prohibited. The hood must be closed and securely latched while the vehicle is hooked to the sled. The complete OEM firewall and complete OEM floor pan is mandatory
Brakes: Four-wheel hydraulic brakes are mandatory.
Chassis: The OEM chassis is mandatory. The engine must be in the OEM location for the body used. The vehicle must retain the full OEM chassis. Wheel tubs, back-half conversions, tube chassis, etc., are prohibited.
Cooling System: Radiators must be in the vicinity of the stock location and be of at least stock size.
Credentials: All drivers must have a valid state drivers license.
Driveline: An OEM transmission and transfer case is mandatory. They must have been an option on a one-ton or smaller pickup.
Driver Restraint System: The OEM restraint system is mandatory and must be worn.
Driveshaft Loops: All trucks must have at least six inch wide u-joint shields around the rear u-joint constructed of at least 1/4-inch steel or 3/8 inch aluminum that will safely contain the u-joint and the end of the rear shaft. All shields must be securely mounted to the vehicle. Any front shaft u-joint that is visible from the side of the truck must be shielded to contain the u-joint and the end of the shaft.
Engine: The engine block must have been available as a factory option on a one-ton or smaller pickup truck. Blocks must circulate coolant freely. Water pumps must be present, but may be powered electrically The use of concrete or other block fillers is prohibited. All factory belt-driven accessories, excluding the air conditioning compressor, must be retained and powered via the crankshaft by a standard serpentine or ‘V’ belt. Electric fans are permitted. Aftermarket radiator assemblies are permitted, but must be securely mounted in the same general area as the OEM unit.
Exhaust: All vehicles must be equipped to direct exhaust upward. Stacks exiting through the hood are permitted however exhausts exiting through the fender-well are prohibited. If using a hood stack two 3/8 inch diameter bolts minimum grade 5 MUST BE installed through the exhaust pipe in a cross pattern within one inch of each other as close to the turbo as is practical but no further than 1 foot from the turbo.
Fire Extinguisher System: A fire extinguisher system is permitted. It must be securely mounted.
Fuel: The fuel must be pump #1/#2 diesel only. Soy/Bio-diesel fuel is permitted. Off-road diesel fuel is prohibited. NITROUS OXIDE is prohibited along with other oxygen extenders and the use of PROPANE is also prohibited. All system components MUST be removed from the truck.
Fuel Injection Pump: Dual high-pressure common-rail fuel pumps or HPOPs are permitted. Pumps from different years in the same engine model may be interchanged. P7100 pumps are allowed to run RSV (AG governors)
Harmonic Balancer: All engines turning 4500 RPM and higher must be equipped with a harmonic balancer or damper meeting SFI Spec 18.1. A shield across the frame under the front of the engine shielding the damper and engine fan area is required.
Hitch: The hitch must be a receiver-style hitch; reinforcements are permitted. Reinforcements must not extend forward of the centerline of the rear axle. Trick hitches are prohibited. The hooking point must be the rear-most point on the vehicle
and must be rearward of the stock location of the tailgate. The hitch must be horizontal to the ground and stationary in all directions. Bumpers may be notched or removed. The hitch’s height from the ground may not exceed 26 inches on 4wd units and 30 inches on 2wd units. The hooking point must have a minimum 3.750-inch inside diameter opening for the sled hook. The hooking point will be measured to the center of the clevis loop.
Interior: A complete interior, including dashboard, door panels, headliner, etc., is mandatory. Two matching front seats are mandatory. Aftermarket seats are permitted; they must be fully upholstered. All factory controls (lights, signals, horn, windows, wipers, etc.) must be retained and be operative. The use of hand-throttle controls are prohibited.
Rear End: The rear end must have been an option on a one-ton or smaller pick up. Rear axle bolts must be covered by a cap or shield.
Steering: The vehicle must retain the full, original OEM steering gear. The vehicle must retain the original OEM power steering assistance, if it was so equipped. Additional stabilizers are permitted. Non-OEM power assist methods are prohibited.
Street Equipment: Complete headlight and taillight assemblies (all) are mandatory and must be operative. Complete OEM windshield and windows are mandatory. Windows must be operative per factory specifications; that is, they must open and close via OEM electrical or mechanical means.
Suspension, Front: The factory suspension configuration must be retained. The upper mounting point for strut assemblies must be in the factory location. Adjustable caster/camber pillow ball mounts are permitted. The lower control arm may be strengthened provided factory-mounting points to chassis are maintained. The lower mounting point for the strut assembly may be modified for improved caster or camber.
Strut tower braces, lower tie bars, sway bars, and limit straps are permitted. Traction bars and devices are permitted. The final decision rests with the Technical Department.
Suspension, Rear: An OEM-style suspension is mandatory. Traction bars and devices are permitted; they must be bolt on only; welds are permitted for attachment to frame or axle housing. Control arms may be strengthened or replaced, provided all original mounting points are retained. Strut tower braces, lower tie bars, sway bars, limit straps, and camber kits are permitted. The rear suspension may be bolted solid to eliminate travel. If a rear suspension has travel it must use at least one working shock absorber per wheel.
Tires: The tires must be DOT street tires. Cut tires are prohibited, if the truck is equipped with dual rear tires they may not exceed 102” from outside to outside.
Tow Vehicles: Tow vehicles are prohibited.
Transfer Case: Non-OEM transfer cases are prohibited. It must have been an option on a one-ton or smaller pickup truck.
Transmission, Automatic: Non-OEM transmissions are prohibited. Aftermarket torque converters, valve bodies and internal components are permitted. Transmission brakes are prohibited. Any non-OEM floor-mounted automatic transmission shifter must be equipped with a spring-loaded positive reverse lockout device to prevent the shifter from accidentally being put into reverse gear. A functional neutral safety switch is mandatory. All transmission lines must be metallic or high-pressure-type hose. All vehicles using an automatic transmission must be equipped with a transmission shield meeting SFI Spec 4.1 and must be labeled accordingly. A blanket-type shield is permitted; it must be appropriately labeled as meeting SFI Spec 4.1 and it must extend from the rear of the block to the front of tail housing with a minimum six-inch overlap where it is fastened. All non-blanket-type shields must incorporate two (or one, per manufacturer’s instructions) 3/4 inch by 1/8 inch straps that bolt to the shield on each side and pass under the transmission pan unless the transmission pan is labeled as meeting SFI Spec 4.1. All vehicles with engines using an automatic transmission must be equipped with a flex plate meeting SFI Spec 29.1 and be covered by a flex plate shield meeting SFI Spec 30.1.
Transmission, Manual: Non-OEM transmissions are prohibited. Aftermarket internal components are permitted. A clutch meeting minimum SFI Spec 1.1 or 1.2 is mandatory on all vehicles. All manual transmissions must be clutch assisted. Sequential shifters are prohibited. All vehicles with engines equipped with a manual transmission must have a flywheel shield labeled as meeting minimum SFI Spec 6.3 or greater. Applications for which an SFI Spec flywheel shield is not available may use a properly attached SFI 4.1 or 4.2 blanket that completely covers the bell housing; it must be attached to the block and extend rearward to the transmission with a minimum six inch overlap where it is fastened.
Turbocharger: The vehicle is limited to a 2.6 inducer bore single turbocharger. The compressor wheel must protrude into a 2.6” bore for 1/8”. The inlet will be measured using a 2.65 inch plug the plug must not be able to enter the inducer bore. A stock map width enhancement (MWE) groove is allowed. No MWE groove will be allowed that has a width greater than .200”. All provisions allowing air into the wheel other than via the bore and the MWE groove are prohibited. The vehicle driver will be responsible for making compressor wheel accessible for tech personal to measure bore and be able to inspect compressor wheel.
Water Injection: Water injection is prohibited. All system components must be removed from the truck.
Wheelbase: The vehicle must retain the original unaltered factory wheelbase and track width. Front dual-wheel spacers may be used only with accompanying positive-offset dually style wheels.
Tech: The top 5 Trucks are subject for Tech inspection and any truck that has a valid complaint! If there is a complaint the accuser must post a $75 tech fee and if the truck is found to be legal for said rules the accuser does not receive a refund but if however the accused is found to be in violation of the said rules the accuser will receive a refund and the accused must then stand good for the $75 tech fee.
All decisions made by Technical Department are final!